12:25 PM
Unknown
If a new component would be installed, there are procedures for that which you need to bear in mind. The procedures have to be followed to install Profile Design Cobra bars properly. That is also a requirement on the policy for the warranty that is provided when you buy one. When you are now knowledgeable on such task, go to its dealer near the area.
You would be provided with a manual that indicates the procedures you must follow. If you prefer to get it done yourself, the tools that will be utilized on that must be prepared. An Allen or a torque wrench should be prepared. You will be needing a sandpaper since that will be utilized in making the parts smooth. When you got all of those tools, you may begin on this.
You should avoid greasing the clamping area. If you would be greasing it, it would only cause the bar to slip from it. You have to make sure that such situation would not happen especially when you are already using your bike. It would cause you to lose control while you are riding the bike. It would be very dangerous on your part if that would happen.
You must be certain that the diameter on a bar clamp will be able to match on the diameter of that stem. You must be checking it so you could surely avoid some problems. This will not fit into it if both of the diameter will not fit each other. Before you will be buying one, you should check their diameter to avoid wasting some money on it.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
One has to inspect its front step clamp as there could be edges that are sharp. Use a sandpaper to get rid of that. The fibers of that aluminum or fiber of the carbon would be damaged if that is not made properly. When you have it on the right position, it has to be clamped to its stem. You must ensure that this will be tight.
You could slide a level to its bar. You could make some adjustments based on your preference when you are uncomfortable with it. This must be placed cautiously. You must bear in mind that the warranty will be invalid when it is broken.
It can be wrap if you prefer that. When you try this, you must ensure that a helmet would be worn. Inspect if it will function properly prior to the time you will be utilizing it on longer distances.
It is important that you would be following those methods. It would be very risky as you would lose control of the bike. It can even cause serious injuries to the person.
You would be provided with a manual that indicates the procedures you must follow. If you prefer to get it done yourself, the tools that will be utilized on that must be prepared. An Allen or a torque wrench should be prepared. You will be needing a sandpaper since that will be utilized in making the parts smooth. When you got all of those tools, you may begin on this.
You should avoid greasing the clamping area. If you would be greasing it, it would only cause the bar to slip from it. You have to make sure that such situation would not happen especially when you are already using your bike. It would cause you to lose control while you are riding the bike. It would be very dangerous on your part if that would happen.
You must be certain that the diameter on a bar clamp will be able to match on the diameter of that stem. You must be checking it so you could surely avoid some problems. This will not fit into it if both of the diameter will not fit each other. Before you will be buying one, you should check their diameter to avoid wasting some money on it.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
One has to inspect its front step clamp as there could be edges that are sharp. Use a sandpaper to get rid of that. The fibers of that aluminum or fiber of the carbon would be damaged if that is not made properly. When you have it on the right position, it has to be clamped to its stem. You must ensure that this will be tight.
You could slide a level to its bar. You could make some adjustments based on your preference when you are uncomfortable with it. This must be placed cautiously. You must bear in mind that the warranty will be invalid when it is broken.
It can be wrap if you prefer that. When you try this, you must ensure that a helmet would be worn. Inspect if it will function properly prior to the time you will be utilizing it on longer distances.
It is important that you would be following those methods. It would be very risky as you would lose control of the bike. It can even cause serious injuries to the person.
About the Author:
Read more about Procedures On Installing Profile Design Cobra Bars You Must Follow.
0 comments :
Post a Comment